Corn Puffed Extruder-manufacture,factory,supplier from China

Directly puffed food is generally required to be dried after extrusion processing. The moisture content of the dough in the extruder is 15%~20%. The product is then dried to reduce the moisture content to 2% to 3% to create the environment needed for a crunchy texture and stable shelf life. Due to the low density of the product, the drying time is usually very short, so it should be carried out in a warm warehouse.Coatings to produce direct-expanded products Extruded and dried products are finally sprayed with oils and seasonings.

The puffed foods such as potato chips, french fries, etc. that we usually see are produced by the puffed food extruder. After a series of operation procedures, the delicious food is presented in front of us.

Application of twin screw extruder:The raw materials suitable for double screw extruding equipment are very wide, there are corn, sorghum, rice, wheat and buckwheat and so on.The puffed material is then ground into powder, which can be used as mixed powder to improve and enhance the sense of eating. It can also be used as a binder for food, viscosifier, binder for casting sand, viscosifier for weaving and dyeing industry, and raw material for floating bait.Principle of twin screw extruder:The twin-screw extruder pushes the material by the screw sleeve and kneads the mixing block.

Puffed food appeared in the market in the 1960s. Later, it quickly became popular in various countries because of its unique taste, simple eating and various patterns. It has long occupied the most frequently purchased snack types with chocolate, wafers and other foods.However, the long-term sales advertisements and puffed food have left us with a stereotyped image. Recently, many consumers said that when they saw the product category as "oil-containing puffed food", they were very worried about whether it was an unhealthy snack.

1. Before operating the corn equipment bulking machine, remove the head, movement, lead screw and other parts, clean them up, dry them and then install them.2. Idling for 1 to 2 minutes first when operating, put the raw materials into the feed mouth, not too fast, when the ring groove of the spiral shaft head is filled, stop feeding, friction preheating. Wait until the nose temperature rises and the pressure inside the cabin builds up before feeding.3. Feed should be continuous and uniform, material must be dry, must pay attention to.4.

For extruder equipment, the model specifications of extruder equipment are classified according to the diameter of the screw. For the sake of explanation, plastic is used as an example below, but the same is true for food extruders.That is to say, the screw diameter of the extruder equipment is the model specification of the extruder equipment. For example, the screw diameter of the 90-type extruder equipment is 90mm.

Twin screw extruder is developed on the basis of single screw extruder. Two screws are placed side by side in the barrel of the twin screw extruder. According to the meshing degree of the two screws can be divided into mutual meshing type and non-meshing type. According to the rotation direction of the two screw shafts, it can be divided into reverse rotation type and co-rotation type.(1) meshing twin screw: Because the meshing gap of the meshing screw is very small, the material has the ability of forced conveying, not easy to produce backflow, leakage phenomenon.

Series double screw extruder introduction:1, mainly by the feeding system, extrusion system, rotary cutting system, heating system, lubrication system, control system.2, extruder feeding system, main drive system, rotary cutting system all adopt frequency control, strong power, smooth operation, power saving.3, automatic lubrication, forced cooling, to ensure the safe operation of the extruder and prolong the life.4, screw alloy material, through special processing, high strength, wear resistance, increase the service life.5, according to different products, with different structure and length

When operating a twin-screw extruder, it should be maintained on time. The maintenance process is carried out after the twin-screw extruder runs continuously for 2500-5000h and shuts down. The screw is extracted to inspect, measure and identify the wear condition of the most critical components, replace the components that have reached the specified wear limit as soon as possible, and repair the damaged components . The maintenance standard of the reducer of the twin-screw extruder is the same as that of the ordinary standard reducer.

The advantages of our twin screw extruder:1. Double screw snack extruder adopts side forced feeding technology, which increases the integrity of the material and greatly increases the output. The position and shape of the feed port also have a great influence on the feed efficiency. Under the same parameters, the feed area increases and the output increases. For the same inlet area, rectangular section has greater feed efficiency than circular section. The use of side twin screw feed is also based on such a consideration.2. Twin screw extruder has strong self-cleaning ability.