Corn Extruder Machine-manufacture,factory,supplier from China

There is only one screw in the barrel of the single screw extruder, it is by the friction of the screw and the barrel of the material to transport materials and form a certain pressure. In general, the friction coefficient between the material and the barrel is greater than that between the material and the screw. Otherwise, the material will be wrapped in the screw together to rotate and not play the role of forward propulsion.Screw is divided into three sections: feeding (feeding) conveying section, compression melting section, metering homogenization section.

1. Before operating the corn equipment bulking machine, remove the head, movement, lead screw and other parts, clean them up, dry them and then install them.2. Idling for 1 to 2 minutes first when operating, put the raw materials into the feed mouth, not too fast, when the ring groove of the spiral shaft head is filled, stop feeding, friction preheating. Wait until the nose temperature rises and the pressure inside the cabin builds up before feeding.3. Feed should be continuous and uniform, material must be dry, must pay attention to.4.

As a food processing equipment, the food extruder has many precautions in use. For example, we need to remove the machine head, movement and lead screw before starting the operation, and we must carefully clean the rice on the machine. dirt and oil, and then re-installed. Only in this way can the material reach the required state and quality. So in the process of Jinan puffing extrusion equipment operation, what should we pay attention to?Matters needing attention during the operation of the extruder are:1. Mainly use corn and potatoes as raw materials to produce small food.2.

When using a twin-screw extruder, the twin-screw extruder needs to install the device correctly, so that it can save energy and time during production.The twin-screw extruder is fully automated from batching, extrusion, puffing, molding, core sandwiching, cutting, spraying to finished products at one time. The production line has the characteristics of many optional models, flexible equipment configuration, wide range of raw materials, many types of products, and simple operation.

Twin screw extruder is developed on the basis of single screw extruder. Two screws are placed side by side in the barrel of the twin screw extruder. According to the meshing degree of the two screws can be divided into mutual meshing type and non-meshing type. According to the rotation direction of the two screw shafts, it can be divided into reverse rotation type and co-rotation type.(1) meshing twin screw: Because the meshing gap of the meshing screw is very small, the material has the ability of forced conveying, not easy to produce backflow, leakage phenomenon.

Feed extruder is a single screw extruder. Mainly used for food puffing, livestock feed or used for puffing single raw materials, but also as a plant oil and drinking wine production of raw materials in the pre-place. Twin-screw extruding extruder, mainly used for the production and processing of high-grade aquatic products, pet materials, especially the processing of viscous materials.What are its characteristics?1.

Series double screw extruder introduction:1, mainly by the feeding system, extrusion system, rotary cutting system, heating system, lubrication system, control system.2, extruder feeding system, main drive system, rotary cutting system all adopt frequency control, strong power, smooth operation, power saving.3, automatic lubrication, forced cooling, to ensure the safe operation of the extruder and prolong the life.4, screw alloy material, through special processing, high strength, wear resistance, increase the service life.5, according to different products, with different structure and length

When operating a twin-screw extruder, it should be maintained on time. The maintenance process is carried out after the twin-screw extruder runs continuously for 2500-5000h and shuts down. The screw is extracted to inspect, measure and identify the wear condition of the most critical components, replace the components that have reached the specified wear limit as soon as possible, and repair the damaged components . The maintenance standard of the reducer of the twin-screw extruder is the same as that of the ordinary standard reducer.

Directly puffed food is generally required to be dried after extrusion processing. The moisture content of the dough in the extruder is 15%~20%. The product is then dried to reduce the moisture content to 2% to 3% to create the environment needed for a crunchy texture and stable shelf life. Due to the low density of the product, the drying time is usually very short, so it should be carried out in a warm warehouse.Coatings to produce direct-expanded products Extruded and dried products are finally sprayed with oils and seasonings.

Extruder belongs to a kind of equipment for processing puffed food. It is a kind of equipment for processing puffed food, such as processing rice, corn, soybean, wheat, etc., in daily life.